Contact Final Project Assignments My Lab About Me

Week 15

Mechanical Design

Assignment 15

Robotic Arm with 7 Servos

Robotic arm with 7 Servos

Poster Describing the Workflow of the Assignment

  • During this my responsibility was Assembling the robot by joining the Laser cut acrylic parts, Servo motors etc


  • The demonstration of working of Robotic arm is shown in the video below. It's the first time that we have completed our assignment before the deadline ;)
    In this week and the upcoming week, we have to make a Machine.So, first we need to design the mechanical parts of our machine in this week.It is basically a group assignment, and every person is required to do a part of assignment and document their contribution.

  • Introduction:
  • In all essential aspects a robotic arm resembles perfectly the human arm in appearance,structure and in many of its functions.A human arm can move freely in 7 axis, but now a days it's not a big deal to see robotic arms which have the same degrees of freedom. A typical robotic arm is made up of seven metal segments, joined by six joints. The computer controls the robot by rotating individual step motors connected to each joint (some larger arms use hydraulics or pneumatics) Your arm's job is to move your hand from place to place. Similarly, the robotic arm's job is to move an end effector from place to place. Designed and realized in the project, the robot arm has the ability to move in 5 axis directions with 7 servo motors.

  • Benefits of Robotic Arm

  • Axes of Robotic Arm
  • The Robotic arm moves in three axes:

    The working of the robotic arm in each individual axes can be understood in a better manner by resembling and anlaysing the movement of a human arm.Each axes charecterize a space through which the robotic arm moves.If we associate the use of axes as a pivot point , then each pivot point is responsible for motion of the robotic arm for a range of motion in the same manner as our wrist and elbow. Increasing the number of axes or pivots , increases the overall range of motion. Here, we will be using 5-axes motion and for that we need 7 servo motors.

  • Different Parts of a Robotic Arm:
    1. Controller
    2. Manipulator
    3. Gripper or end effector
    4. Power supply or energy source, and
    5. Data acquisition system (vision sensors system).
    6. Programming

  • Kinematics of the Robotic Arm
  • The human arm consists of two distinct parts: the wrist with three minor joints, and the arm’s two major joints, i.e., the shoulder and the elbow. The function of the human wrist is to provide the orientation of the object held by the hand. Various functions of the arm may be explained as follows:
    similarities between a human arm and a Robotic arm

    >> Hold your right arm and hand straight out. Keeping the palm in downward direction, this is the reference angular position (0o). Then rotate your wrist as far in both clockwise and anticlockwise directions. This is called roll motion and limits of rotation as -180o and +90o respectively, i.e., Roll (angle) = 180o – 0o – (-90) = 270o.

    >> Hold your right arm and hand straight out. Keeping the palm in downward direction, this is the reference angular position (0o). Then rotate your wrist as far in both clockwise and anticlockwise directions. This is called roll motion and limits of rotation as -180o and +90o respectively, i.e., Roll (angle) = 180o – 0o – (-90) = 270o.

    >> Again holding the right arm in the reference position (0o) and without rolling the hand. Move the wrist from the initial straight position as far as possible in a downward and then in an upward direction. Called pitch motion and its limit positions are at – 90o and 50o, i.e., Pitch (angle) = 90o – 0o – (- 50) = 140o

    >> Holding your right arm straight out and the wrist making neither a roll nor a pitch motion. Let the fingers point horizontally as far as possible to the right and then to the left. This is the yaw motion and its limit positions are at – 45o and + 15o, i.e., Yaw (angle) = + 45o – 0o – (- 15) = 60o

    Defining the joints and DOF of the Robotic arm


    Roll, pitch and yaw are considered independent motions and therefore referred to as degrees of freedom. The second part of the human arm has two major joints with three degrees of freedom, two in the shoulder and one in the elbow. But the robot has a shoulder with one degree of freedom only, and thus the robot waist is introduced as a substitute for one of the shoulder’s independent motions. In the case of a human the waist has a different function, i.e., it is for manoeuvrability by counter-balancing the human body against the gravitational load in changing body postures. The counter balance in robots is some time used by incorporating a mechanical loop in its structure.

    The human arm has five fingers with three degrees of freedom in each one of them. These fingers are used to grip a part of any configuration either in conjunction of each other or individually independently depending on type of job, object to be handled and degrees of freedom to be used. The fingers are used independently with dexterity; contrary to this, the robot gripper has independent mobility and no dexterity except for very rare tasks. In 85% of pick-n-place industrial robots, the gripper does not have more than two or three fingers because in industrial work only the thumb, first and middle fingers are used. An important feature of the robot structure is the ratio of the length of upper arm to that of the fore arm, which is around 1.2. This implies that robot’s forearm should be either equal to or slightly shorter than the upper arm. If this rule is not followed there will be robot performance impairment. Remember, the robot is a mechanical system representing human arm, however, it cannot reach the human arm’s performance capabilities as this consists of large scale hierarchical system composed of large number of linear and non linear elements.



    Note: The description for understanding the Kinematics and Axis of robotic arm has been taken from Robotics: fundamentals, principles of working & components

  • Task Division:
  • The whole project comprises of the following parts and divided in our Group. It's really an interesting and challenging task to do.
    1. CAD Design of the Robotic arm, Laser cut and 3D print the parts. (This Task has been Assigned to Mr. Noor Ahmed Raza Pirwani)
    2. Assembling the parts to make the Robotic arm (This task has been assigned to Ms. Sehrish Khan, Rasheed Qazi)
    3. Electronics Production , designing the Controller (This task has been assigned to Mr.Nadir Ali)
    4. Programming of the Controller(This task has been assigned to Noor Ahmed Pirwani and Rasheed Qazi)

  • CAD Design of the Robotic Arm:
  • The whole model was increased by 1/3rd of its original size. We are using 6mm blue acrylic for this project. Scaling factor is decided as 1/3rd because of hardware compatibility issues

    Challenges faced while Scaling:

    While scaling the Design , there were some limitations which were to be kept in mind. These are discussed below:

    Resolving the issues of Scaling:

    After analysing the design and hardware constraints, the following steps were taken to resolve the scaling issues: Instead of increasing the scaling factor of the whole part, first the internal parts designated for screws and size of other internal parts were decreased by dividing them with 1.33. After decreasing the internal parts by 1/3 , we increased the whole part to 1/3rd so that it can make screw holes, motor placement, shaft placement and other internal parts to there actual size.

    The scaling process is illustrated by the pictures below:


    1- these holes are used to 3mm we divide it to 1div3 to make it 2.25mm

    2- the original model was on 3mm thickness so we change it to 4.5 which multiplied with our scaling factor to become 6mm

    3- then we scale it to 1.33 percent of actual size, this step made thickness 6mm and made screwholes to again 3mm

    4- screw holes are nearly 3mm as measured. other parts are also scaled it like this

    There are other tools of solidworks used also while scaling like ; center line to check the boxes are alligned, mate tool for assembling the parts etc. Finally, the whole model was scaled up by the scale factor of 1/3, keeping the scale ratio constant.

  • LASER cutting of parts:
  • After scaling of all the parts in Solidworks, the parts were joined together and made an Assembly by creating the Mates as shown in the pictures above.The next step was to cut all the individual parts on Laser cut.Follwing are the necessary details of Laser cut of the parts.
    Laser cut doing the Job

    Laser cut Job is done , parts after Laser Cut

  • LASER cutting of parts:
  • Now, its time to assemble the parts to make the robotic arm with 6 dof. Following were the components required for assembling:
    Components for joining parts

    The parts are being assembled, as shown below:
    Assembling the parts

    Assembling the parts

    The seperate page of our group assignment for Mechanical and Machine design can be visited by clicking Here. That's all for week15..
  • All the Files of Week 15 can be downloaded from Here.




  • Creative Commons License
    This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.